For any migrations done on these screens to new servers, contact support@dise.com since a special server certificate is needed.

Supported models

Samsung screens with SSP2 and SSP3 are supported.

DHE, DME, DBE, DBD, OMD-W, OMD-K, OHD, OME, OHE series

For SSP4, see this page.

Which Samsung display products are compatible with SSSP? - Samsung

Firmware upgrade

Before setting up Lite, please make sure that the device has a recent firmware! Contact support for more information.

Installation

To install Lite on the Samsung SSP, please

1. Connect Ethernet cable.

2. Connect power supply.

3. Start the screen and go through the initial setup guide.
   The most important settings are to change Auto Power Off to "Off (recommended)".

4. Select URL Launcher

5. Type in the URL to the player software.
   This is one of the following:

   • http://go.dise.tv
     Used in the normal case. The player needs to have internet access.

   • http://go.dise.tv/beta/x.y.z
     ONLY use this when you have been instructed by DISE Support to use a special version. The player needs to have internet access.

   • http://server-ip-or-fqdn/player
     ONLY use this when the player has no internet access and server is installed on-premises. 

6. If the screen is in portrait mode, please add /portrait to the end of the URL (for example, http://go.dise.tv/portrait)

7. Click URL Launcher to start the player.

8. After a little while, a 6-digit code, a discovery code, will be presented on the screen.

   This code is unique to the player. Make a note of it or take a photo because we will need it in the next step, which is in DISE CX Portal.
9. Log in to Portal and select the Players tab.  
10. Click Add to create a new player.  
11. In the dialog appearing, enter a name, the 6-digit discovery code, and click Save.
    If you have already created a content playlist you want to play on the screen you may also specify it here - otherwise you can configure this later.
12. You will notice that the player software on the screen will subsequently receive the settings, register with CX Portal and download some content.

Offline server registration

In the case when the screen does not have internet access, replace steps 8-12 with these:

• Since the manual registration in CX Portal doesn't work with SSSP screens we can do the registration using a USB drive.
• Please download the attached sssp_USB_config.zip file and extract to a temporary folder.
• Use the create_sssp_config.bat file to create the files directly on the USB memory or rename the files according to your requirements and copy those to the USB drive. If you use the .bat file, make sure all the files were created correctly on the drive after it is done. 
• We recommend that you create a temporary admin user for the setup procedure that you can remove later.
• Start the screen.
• To see log of the screen press the INFO button on the remote.
• When you see the discovery code, insert the USB drive with the files. 
• Within a couple of seconds the screen reads the contents of the USB drive and from this get the details to connect to CX Portal.
• If there is an error, please review the files on the USB to see that the details is correct and then using the remote press "Clear settings" button to reset the screen. Then start again by inserting the USB drive.
• The player will register in CX Portal by the name specified by the dise_discovery_name_PLAYERNAME file.
• Log in to CX Portal, locate the player, then set a new playlist by going into it, click Edit, then select a new playlist.

Portrait mode

To change the screen to portrait, please.
OBS! If the screen is in portrait mode, please add /portrait to the end of the URL (for example http://go.dise.tv/portrait) 

1. Exit the playback to the Home screen by clicking the Home button on the remote.
2. Select More settings.
3. Select OnScreen Display.
4. Change Display Orientation to "Portrait".
5. Add /portrait to the player software URL Launcher as described in step 6 above.
6. Now menu and player are in portrait mode.

Player control

To view log and options in the player when it is running, press INFO on the remote.

Clear settings

Removes all settings and restarts to show a new discovery code.

Clear content cache

Removes all content and restarts to download all content again.

Uninstall

1. Exit the playback to the Home screen by clicking the Home button on the remote.
2. Click Change URL.
3. Type in:
   $DEL
4. Click Done.
5. Click URL Launcher.